| 环氧自流平地坪漆标准工艺厚度在1.5mm左右 |
| 添加时间：2019/8/7 14:34:47 浏览次数： |
| 1、地坪铣刨处理：用高速多头地坪专业铣刨机对地面进行铣刨处理，去除地坪外观混凝土附浆1-2mm并对地面找平，此工艺施工中采用16的铣刨头以增长混凝土下层的毛度，并进步地坪的平整度，用专用抛丸机对地坪进行处理，增长下层毛度。 1. Floor milling processing: Milling the ground with high-speed multi-head professional ground milling machine, removing the surface concrete slurry of 1-2 mm and leveling the ground. In this process, 16 milling planers are used to increase the wool of the lower layer of concrete and improve the flatness of the ground. The ground is treated with special shot blasting machine. Long lower wool. 2、环氧底涂：将环氧底涂材料安装说明书配比配制并搅拌均匀，然后用滚筒均匀地滚筒于地坪外观，此工艺可以重复施工，直至完全封闭混凝土毛细孔，伸缩缝、施工缝采用贴布处理。(材料用量0.2kg/㎡，结膜厚度0mm)。 2. Epoxy primer: mix and mix the epoxy primer material in the installation instructions evenly, and then use the drum to uniformly surface the floor. This process can be repeated construction until the concrete capillaries are completely closed, and the expansion joints and construction joints are treated by sticking cloth. (Material dosage was 0.2 kg/, conjunctival thickness was 0 mm). 3、砂浆中涂：在配置好的环氧中涂材料中加入肯定比例的石英砂并搅拌均匀，然后用镘刀将配置好的砂浆中涂材料均匀地镘涂于完全固化后的底涂外观，待其完全固化后打磨吸尘。(材料用量0.4kg/㎡，结膜厚度0.5mm)。 3. Intermediate coating of mortar: Quartz sand with definite proportion is added to the coated material of epoxy resin and stirred evenly. Then the coated material of the prepared mortar is uniformly coated on the appearance of the fully cured base coating with a trowel knife, and then it is sanded and cleaned after it is completely cured. (Material dosage was 0.4 kg/, conjunctival thickness was 0.5 mm). 4、批涂：在配置好的环氧中涂材料中加入肯定比例的碳酸钙粉并搅拌均匀，然后用镘刀将配置好的中涂材料均匀地批涂于完全固化后的底涂外观，此工艺施工后要达到手感光滑，避免沙眼、马蜂窝征象。(材料用量0.2kg/㎡，结膜厚度0.15mm)。 4. Batch coating: add a certain proportion of calcium carbonate powder into the prepared epoxy coating material and mix evenly. Then batch coating material with a trowel knife is evenly applied to the fully cured appearance of the base coating. After construction, the process should achieve smooth hand feel and avoid trachoma and honeycomb symptoms. (Material dosage was 0.2 kg/, conjunctival thickness was 0.15 mm). 5、环氧面涂：首先将彩色面涂自流平材料按肯定比例正确配置并搅拌均匀，然后用镘刀将配置好的彩色面涂材料均匀地镘涂于上工艺外观，达到颜色均匀同等，有晶面结果。(材料用量1kg/㎡，结膜厚度0.85mm)。 5. Epoxy surface coating: Firstly, the self-leveling material of the color surface is correctly collocated and stirred evenly in a certain proportion. Then, the collocated color surface coating material is evenly coated on the surface of the coating process with a trowel knife to achieve uniform and equal color and crystalline results. (Material dosage was 1 kg/, conjunctival thickness was 0.85 mm). |
| 上一页 防腐蚀地坪具体应注意以下几点 |
| 下一页 防腐地坪漆涂刷后起泡现象主要是因为两个因素 |
Copyright © 技术支持：遨游网络