| 环氧地坪漆施工工艺详细流程！ |
| 添加时间：2019/2/16 14:03:23 浏览次数： |
| 环氧地坪漆施工流程：环氧地坪漆———底漆/中涂/面涂。首先都要打磨地面平整清洁干净环氧底涂 Construction process of epoxy floor paint: epoxy floor paint - primer / middle coating / surface coating. First of all, the ground should be polished flat, clean and epoxy primer. 1、施工前需确保地面干净，如有杂物粘附需清除； 1. Make sure the ground is clean before construction. If there is any debris adhesion, it should be removed. 2、将环氧树脂和固化剂按正确比例混合搅拌， 2. Mix epoxy resin and curing agent in the right proportion. 3、搅拌均匀后，采用刮刀或滚筒施涂的方法施涂。 3. After mixing evenly, apply it with scraper or drum. 4、要求浸透加强附作力。 4. Require immersion to strengthen the adhering force. 5、待第一遍干固后再施涂环氧中涂层。 5. Apply epoxy coating after first drying. 环氧中涂层 Epoxy coating 1、施工前需确保地面干净，如有杂物粘附需清除； 1. Make sure the ground is clean before construction. If there is any debris adhesion, it should be removed. 2、将环氧树脂和固化剂按正确比例混合搅拌，并按配比加上一定的石英； 2. Mix the epoxy resin and curing agent in the right proportion and add quartz according to the proportion. 3、砂搅拌均匀后倾倒在地面上，使用镘刀按设计的厚度将材料均匀镘开，以增加强度和耐冲击力；使地面更加结实，抗压。 3. The sand is evenly stirred and dumped on the ground. The material is evenly shoveled with a shovel cutter according to the designed thickness to increase the strength and impact resistance, and tocangzhou.89ix.comshiyanjiw.89ix.comshoubanhulu.07858.netdianbiaox.37ix.com.cnzengbaiji.37ix.c om.cnyawenzhim.37ix.com.cn make the ground stronger and more compressive. 4、中涂层干固后，采用打磨，把表面的流挂物、颗粒打磨平整。4. After the middle coating is dry and solidified, the surface hangings and particles are polished flat by grinding. 5、灰尘处理干净。 5. Clean up the dust. 环氧中涂腻子层 Putty coating in epoxy 1、在洁净的地面上，将环氧树脂和石英粉按正确的配比搅拌均匀后，采用批刀均匀镘刮在地面上，以增加中涂与面层之间的结合，并进一步调整地面的平整度； 1. After mixing the epoxy resin and quartz powder in the right proportion on the clean ground, the batch knife is used to scrape evenly on the ground to increase the combination between the middle coating and the surface layer and further adjust the levelness of the ground. 2、视实际需要施工遍数，要求达到平整无孔洞，无批刀印及砂磨印为准。 2. According to the actual needs of construction times, requirements to achieve flat without holes, no batch of knife printing and sanding printing shall prevail. 环氧面涂层 Epoxy Surface Coating 1、施工前需保持干净，如有杂物粘附需清除； 1. Keep clean before construction, and remove debris if they stick to each other. 2、将面涂材料的B组份先搅拌均匀；再加入固化剂混合，充分搅拌； 2. Mix the B component of the surface coating material evenly at first, then add the curing agent to mix, and mix fully. 3、使用辊筒将材料均匀涂布； 3. Use roller to coat material evenly. 4、第一遍涂层干固后，再施工第二次面涂层。 4. After the first coat is dried and solidified, the second coat is applied. 5、自流平面涂用镘刀刮镘一遍 5. Self-flow plane coating with trowel scraping once 6、注意先后施工交接处的处理；涂层要求均匀，无流挂。 6. Attention should be paid to the treatment at the junction of construction successively; the coating should be uniform and without flow hanging. |
| 上一页 环氧树脂玻纤防腐地坪施工工艺 |
| 下一页 透水地坪施工步骤 |
Copyright © 技术支持：遨游网络