联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
防腐地坪施工工艺
防腐地坪施工工艺：
Anticorrosion floor construction technology:
1、基础处理：采用打磨机对浮物，凹凸不平的地面进行深度打
1. Foundation treatment: use the sanding machine to carry out deep beating on floating objects and uneven ground.
防腐地坪
Anticorrosive floor
防腐地坪(5张)
Anticorrosion floor (5)
磨，清理灰尘杂物，如果凹入太深的区域用中涂层材料加石英砂修补，找平，固化后再进行底涂层施工；
Grinding, cleaning dust and debris, if the concave area is too deep, use the middle coating material Kashi Eisa to repair, leveling and solidifying, then undercoat the construction.
2、底涂层：用树脂胶料加适量稀释剂滚涂一遍，增加附着力以及封闭基础地面的潮气，水气，避免基础层与环氧涂层起壳，脱层；
2, bottom coating: roll coating with resin glue plus appropriate diluent, increase the adhesion and seal the moisture of the ground, water and gas, avoid the foundation and epoxy coating, delayer;
3、玻纤布和中涂层施工：先摊铺玻纤布然后刷涂防腐砂浆中涂，每铺一层就在涂刷一道防腐砂浆中涂，直达到玻纤防腐地坪厚度规定的厚度为止；
3, the construction of glass fiber cloth and medium coating: first spread the glass fiber cloth and paint the anticorrosion mortar. Each layer is painted in a coating of anticorrosion mortar to reach the thickness stipulated in the thickness of the glass fiber anticorrosion floor.
4、腻子层：用环氧防腐中涂材料调配石英砂或双飞粉刮批腻子层，按需要施工二至三道，要求达到平整无孔洞、以利面涂施工；
4, putty layer: use the epoxy coating material to mix quartz sand or double fly powder to scrape and scrape the putty layer. It is required to construct two to three channels according to the requirement.
5 防腐面涂层：用防腐面漆树脂胶料或色漆涂布二道；注：所用树脂依设计而定，涂刮完毕后用带齿滚洞消泡；
5 anticorrosive coating: two coating with anticorrosive finish, resin adhesive or color paint; note: the resin used is designed according to the design, and after the coating is finished, roll the hole with teeth.
6、在玻纤防腐地坪施工过程中，注意材料调配的比例，还有搅拌材料的手法和搅拌的时间，避免防腐材料在加入助剂时产生化学反应出现大量气泡，增加施工难度，还要花大量的时间用带齿滚洞消泡，还有一种情况就是，在搅拌材料时不均匀，涂刷后才产生气泡，待固化就会影面层的表面效果；
6. During the construction process of glass fiber anticorrosion ground floor, the proportion of material allocation, the technique of mixing material and the time of mixing, avoid the chemical reaction of anticorrosion materials to produce a large number of bubbles in chemical reaction, increase the difficulty of construction, and also take a lot of time to use the toothed rolling hole to eliminate bubbles, and one of the cases is that it is stirring. When mixing material is uneven, it will produce bubbles after brushing. It will affect the surface effect of the surface when it is solidified.
Anticorrosion floor construction technology:
1、基础处理：采用打磨机对浮物，凹凸不平的地面进行深度打
1. Foundation treatment: use the sanding machine to carry out deep beating on floating objects and uneven ground.
防腐地坪
Anticorrosive floor
防腐地坪(5张)
Anticorrosion floor (5)
磨，清理灰尘杂物，如果凹入太深的区域用中涂层材料加石英砂修补，找平，固化后再进行底涂层施工；
Grinding, cleaning dust and debris, if the concave area is too deep, use the middle coating material Kashi Eisa to repair, leveling and solidifying, then undercoat the construction.
2、底涂层：用树脂胶料加适量稀释剂滚涂一遍，增加附着力以及封闭基础地面的潮气，水气，避免基础层与环氧涂层起壳，脱层；
2, bottom coating: roll coating with resin glue plus appropriate diluent, increase the adhesion and seal the moisture of the ground, water and gas, avoid the foundation and epoxy coating, delayer;
3、玻纤布和中涂层施工：先摊铺玻纤布然后刷涂防腐砂浆中涂，每铺一层就在涂刷一道防腐砂浆中涂，直达到玻纤防腐地坪厚度规定的厚度为止；
3, the construction of glass fiber cloth and medium coating: first spread the glass fiber cloth and paint the anticorrosion mortar. Each layer is painted in a coating of anticorrosion mortar to reach the thickness stipulated in the thickness of the glass fiber anticorrosion floor.
4、腻子层：用环氧防腐中涂材料调配石英砂或双飞粉刮批腻子层，按需要施工二至三道，要求达到平整无孔洞、以利面涂施工；
4, putty layer: use the epoxy coating material to mix quartz sand or double fly powder to scrape and scrape the putty layer. It is required to construct two to three channels according to the requirement.
5 防腐面涂层：用防腐面漆树脂胶料或色漆涂布二道；注：所用树脂依设计而定，涂刮完毕后用带齿滚洞消泡；
5 anticorrosive coating: two coating with anticorrosive finish, resin adhesive or color paint; note: the resin used is designed according to the design, and after the coating is finished, roll the hole with teeth.
6、在玻纤防腐地坪施工过程中，注意材料调配的比例，还有搅拌材料的手法和搅拌的时间，避免防腐材料在加入助剂时产生化学反应出现大量气泡，增加施工难度，还要花大量的时间用带齿滚洞消泡，还有一种情况就是，在搅拌材料时不均匀，涂刷后才产生气泡，待固化就会影面层的表面效果；
6. During the construction process of glass fiber anticorrosion ground floor, the proportion of material allocation, the technique of mixing material and the time of mixing, avoid the chemical reaction of anticorrosion materials to produce a large number of bubbles in chemical reaction, increase the difficulty of construction, and also take a lot of time to use the toothed rolling hole to eliminate bubbles, and one of the cases is that it is stirring. When mixing material is uneven, it will produce bubbles after brushing. It will affect the surface effect of the surface when it is solidified.
